| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
|
| |
We set this field, but nothing ever checked it.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
We recently corrected some errors handling the endianness of IPv4
addresses. These are very easy errors to make since although we mostly
store them in network endianness, we sometimes need to manipulate them in
host endianness.
To reduce the chances of making such mistakes again, change to always using
a (struct in_addr) instead of a bare in_addr_t or uint32_t to store network
endian addresses. This makes it harder to accidentally do arithmetic or
comparisons on such addresses as if they were host endian.
We introduce a number of IN4_IS_ADDR_*() helpers to make it easier to
directly work with struct in_addr values. This has the additional benefit
of making the IPv4 and IPv6 paths more visually similar.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Since kernel version 5.7, commit c427bfec18f2 ("net: core: enable
SO_BINDTODEVICE for non-root users"), we can bind sockets to
interfaces, if they haven't been bound yet (as in bind()).
Introduce an optional interface specification for forwarded ports,
prefixed by %, that can be passed together with an address.
Reported use case: running local services that use ports we want
to have externally forwarded:
https://github.com/containers/podman/issues/14425
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Port numbers (for both TCP and UDP) are 16-bit, and so fit exactly into a
'short'. USHRT_MAX is therefore the maximum port number and this is widely
used in the code. Unfortunately, a lot of those places don't actually
want the maximum port number (USHRT_MAX == 65535), they want the total
number of ports (65536). This leads to a number of potentially nasty
consequences:
* We have buffer overruns on the port_fwd::delta array if we try to use
port 65535
* We have similar potential overruns for the tcp_sock_* arrays
* Interestingly udp_act had the correct size, but we can calculate it in
a more direct manner
* We have a logical overrun of the ports bitmap as well, although it will
just use an unused bit in the last byte so isnt harmful
* Many loops don't consider port 65535 (which does mitigate some but not
all of the buffer overruns above)
* In udp_invert_portmap() we incorrectly compute the reverse port
translation for return packets
Correct all these by using a new NUM_PORTS defined explicitly for this
purpose.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
| |
|
|
|
|
|
|
|
|
| |
Now that we've delayed initialization of the UDP specific "reverse" map
until udp_init(), the only difference between the various 'remap' functions
used in conf_ports() is which array they target. So, simplify by open
coding the logic into conf_ports() with a pointer to the correct mapping
array.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Because it's connectionless, when mapping UDP ports we need, in addition
to the table of deltas for destination ports needed by TCP, we need an
inverted table to translate the source ports on return packets.
Currently we fill out the inverted table at the same time we construct the
main table in udp_remap_to_tap() and udp_remap_to_init(). However, we
don't use either table until after we've initialized UDP, so we can delay
the construction of the reverse table to udp_init(). This makes the
configuration more symmetric between TCP and UDP which will enable further
cleanups.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The configuration for how to forward ports in and out of the guest/ns is
divided between several different variables. For each connect direction
and protocol we have a mode in the udp/tcp context structure, a bitmap
of which ports to forward also in the context structure and an array of
deltas to apply if the outward facing and inward facing port numbers are
different. This last is a separate global variable, rather than being in
the context structure, for no particular reason. UDP also requires an
additional array which has the reverse mapping used for return packets.
Consolidate these into a re-used substructure in the context structure.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
enum conf_port_type is local to conf.c and is used to track the port
forwarding mode during configuration. We don't keep it around in the
context structure, however the 'init_detect_ports' and 'ns_detect_ports'
fields in the context are based solely on this. Rather than changing
encoding, just include the forwarding mode into the context structure.
Move the type definition to a new port_fwd.h, which is kind of trivial at
the moment but will have more stuff later.
While we're there, "conf_port_type" doesn't really convey that this enum is
describing how port forwarding is configured. Rename it to port_fwd_mode.
The variables (now fields) of this type also have mildly confusing names
since it's not immediately obvious whether 'ns' and 'init' refer to the
source or destination of the packets. Use "in" (host to guest / init to
ns) and "out" (guest to host / ns to init) instead.
This has the added bonus that we no longer have locals 'udp_init' and
'tcp_init' which shadow global functions.
In addition, add a typedef 'port_fwd_map' for a bitmap of each port number,
which is used in several places.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
| |
|
|
|
|
|
|
|
|
|
|
| |
Reported by David but also by Coverity (CWE-119):
In conf_ports: Out-of-bounds access to a buffer
...not in practice, because the allocation size is rounded up
anyway, but not nice either.
Reported-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
This feature is available in slirp4netns but was missing in passt and
pasta.
Given that we don't do dynamic memory allocation, we need to bind
sockets while parsing port configuration. This means we need to
process all other options first, as they might affect addressing and
IP version support. It also implies a minor rework of how TCP and UDP
implementations bind sockets.
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
|
| |
|
|
| |
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Implement a packet abstraction providing boundary and size checks
based on packet descriptors: packets stored in a buffer can be queued
into a pool (without storage of its own), and data can be retrieved
referring to an index in the pool, specifying offset and length.
Checks ensure data is not read outside the boundaries of buffer and
descriptors, and that packets added to a pool are within the buffer
range with valid offset and indices.
This implies a wider rework: usage of the "queueing" part of the
abstraction mostly affects tap_handler_{passt,pasta}() functions and
their callees, while the "fetching" part affects all the guest or tap
facing implementations: TCP, UDP, ICMP, ARP, NDP, DHCP and DHCPv6
handlers.
Suggested-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
Unions and structs, you all have names now.
Take the chance to enable bugprone-reserved-identifier,
cert-dcl37-c, and cert-dcl51-cpp checkers in clang-tidy.
Provide a ffsl() weak declaration using gcc built-in.
Start reordering includes, but that's not enough for the
llvm-include-order checker yet.
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
|
| |
|
|
|
|
|
| |
Most are just about style and form, but a few were actually
serious mistakes (NDP-related).
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
|
| |
|
|
|
|
|
|
|
|
| |
SPDX tags don't replace license files. Some notices were missing and
some tags were not according to the SPDX specification, too.
Now reuse --lint from the REUSE tool (https://reuse.software/) passes.
Reported-by: Martin Hauke <mardnh@gmx.de>
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
|
| |
|
|
|
|
|
|
|
|
| |
Detecting bound ports at start-up time isn't terribly useful: do this
periodically instead, if configured.
This is only implemented for TCP at the moment, UDP is somewhat more
complicated: leave a TODO there.
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
Until now, messages would be passed to protocol handlers in a single
batch only if they happened to be dequeued in a row. Packets
interleaved between different connections would result in multiple
calls to the same protocol handler for a single connection.
Instead, keep track of incoming packet descriptors, arrange them in
sequences, and call protocol handlers only as we completely sorted
input messages in batches.
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
|
| |
|
|
| |
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
|
| |
|
|
|
|
|
|
| |
Traffic with loopback source address will be forwarded to the direct
loopback connection in the namespace, and the tap interface is used
for the rest.
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
|
| |
|
|
|
|
|
|
|
|
|
| |
Allow to bind IPv4 and IPv6 ports to tap, namespace or init separately.
Port numbers of TCP ports that are bound in a namespace are also bound
for UDP for convenience (e.g. iperf3), and IPv4 ports are always bound
if the corresponding IPv6 port is bound (socket might not have the
IPV6_V6ONLY option set). This will also be configurable later.
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
|
| |
|
|
|
|
|
|
|
|
| |
Packets are received directly onto pre-cooked, static buffers
for IPv4 (with partial checksum pre-calculation) and IPv6 frames,
with pre-filled Ethernet addresses and, partially, IP headers,
and sent out from the same buffers with sendmmsg(), for both
passt and pasta (non-local traffic only) modes.
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
PASTA (Pack A Subtle Tap Abstraction) provides quasi-native host
connectivity to an otherwise disconnected, unprivileged network
and user namespace, similarly to slirp4netns. Given that the
implementation is largely overlapping with PASST, no separate binary
is built: 'pasta' (and 'passt4netns' for clarity) both link to
'passt', and the mode of operation is selected depending on how the
binary is invoked. Usage example:
$ unshare -rUn
# echo $$
1871759
$ ./pasta 1871759 # From another terminal
# udhcpc -i pasta0 2>/dev/null
# ping -c1 pasta.pizza
PING pasta.pizza (64.190.62.111) 56(84) bytes of data.
64 bytes from 64.190.62.111 (64.190.62.111): icmp_seq=1 ttl=255 time=34.6 ms
--- pasta.pizza ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 34.575/34.575/34.575/0.000 ms
# ping -c1 spaghetti.pizza
PING spaghetti.pizza(2606:4700:3034::6815:147a (2606:4700:3034::6815:147a)) 56 data bytes
64 bytes from 2606:4700:3034::6815:147a (2606:4700:3034::6815:147a): icmp_seq=1 ttl=255 time=29.0 ms
--- spaghetti.pizza ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 28.967/28.967/28.967/0.000 ms
This entails a major rework, especially with regard to the storage of
tracked connections and to the semantics of epoll(7) references.
Indexing TCP and UDP bindings merely by socket proved to be
inflexible and unsuitable to handle different connection flows: pasta
also provides Layer-2 to Layer-2 socket mapping between init and a
separate namespace for local connections, using a pair of splice()
system calls for TCP, and a recvmmsg()/sendmmsg() pair for UDP local
bindings. For instance, building on the previous example:
# ip link set dev lo up
# iperf3 -s
$ iperf3 -c ::1 -Z -w 32M -l 1024k -P2 | tail -n4
[SUM] 0.00-10.00 sec 52.3 GBytes 44.9 Gbits/sec 283 sender
[SUM] 0.00-10.43 sec 52.3 GBytes 43.1 Gbits/sec receiver
iperf Done.
epoll(7) references now include a generic part in order to
demultiplex data to the relevant protocol handler, using 24
bits for the socket number, and an opaque portion reserved for
usage by the single protocol handlers, in order to track sockets
back to corresponding connections and bindings.
A number of fixes pertaining to TCP state machine and congestion
window handling are also included here.
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
|
| |
|
|
|
|
|
|
|
|
| |
This is in preparation for scatter-gather IO on the UDP receive path:
save a getsockname() syscall by setting a flag if we get the numbering
of all bound sockets in a strict sequence (expected, in practice) and
repurpose the tap buffer to be also a socket receive buffer, passing
it down to protocol handlers.
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
As we support UDP forwarding for packets that are sent to local
ports, we actually need some kind of connection tracking for UDP.
While at it, this commit introduces a number of vaguely related fixes
for issues observed while trying this out. In detail:
- implement an explicit, albeit minimalistic, connection tracking
for UDP, to allow usage of ephemeral ports by the guest and by
the host at the same time, by binding them dynamically as needed,
and to allow mapping address changes for packets with a loopback
address as destination
- set the guest MAC address whenever we receive a packet from tap
instead of waiting for an ARP request, and set it to broadcast on
start, otherwise DHCPv6 might not work if all DHCPv6 requests time
out before the guest starts talking IPv4
- split context IPv6 address into address we assign, global or site
address seen on tap, and link-local address seen on tap, and make
sure we use the addresses we've seen as destination (link-local
choice depends on source address). Similarly, for IPv4, split into
address we assign and address we observe, and use the address we
observe as destination
- introduce a clock_gettime() syscall right after epoll_wait() wakes
up, so that we can remove all the other ones and pass the current
timestamp to tap and socket handlers -- this is additionally needed
by UDP to time out bindings to ephemeral ports and mappings between
loopback address and a local address
- rename sock_l4_add() to sock_l4(), no semantic changes intended
- include <arpa/inet.h> in passt.c before kernel headers so that we
can use <netinet/in.h> macros to check IPv6 address types, and
remove a duplicate <linux/ip.h> inclusion
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Avoid a bunch of syscalls on forwarding paths by:
- storing minimum and maximum file descriptor numbers for each
protocol, fall back to SO_PROTOCOL query only on overlaps
- allocating a larger receive buffer -- this can result in more
coalesced packets than sendmmsg() can take (UIO_MAXIOV, i.e. 1024),
so make sure we don't exceed that within a single call to protocol
tap handlers
- nesting the handling loop in tap_handler() in the receive loop,
so that we have better chances of filling our receive buffer in
fewer calls
- skipping the recvfrom() in the UDP handler on EPOLLERR -- there's
nothing to be done in that case
and while at it:
- restore the 20ms timer interval for periodic (TCP) events, I
accidentally changed that to 100ms in an earlier commit
- attempt using SO_ZEROCOPY for UDP -- if it's not available,
sendmmsg() will succeed anyway
- fix the handling of the status code from sendmmsg(), if it fails,
we'll try to discard the first message, hence return 1 from the
UDP handler
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
|
| |
|
|
|
|
|
|
|
|
| |
Receive packets in batches from AF_UNIX, check if they can be sent
with a single syscall, and batch them up with sendmmsg() in case.
A bit rudimentary, currently only implemented for UDP, but it seems
to work.
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
|
|
|
This is a reimplementation, partially building on the earlier draft,
that uses L4 sockets (SOCK_DGRAM, SOCK_STREAM) instead of SOCK_RAW,
providing L4-L2 translation functionality without requiring any
security capability.
Conceptually, this follows the design presented at:
https://gitlab.com/abologna/kubevirt-and-kvm/-/blob/master/Networking.md
The most significant novelty here comes from TCP and UDP translation
layers. In particular, the TCP state and translation logic follows
the intent of being minimalistic, without reimplementing a full TCP
stack in either direction, and synchronising as much as possible the
TCP dynamic and flows between guest and host kernel.
Another important introduction concerns addressing, port translation
and forwarding. The Layer 4 implementations now attempt to bind on
all unbound ports, in order to forward connections in a transparent
way.
While at it:
- the qemu 'tap' back-end can't be used as-is by qrap anymore,
because of explicit checks now introduced in qemu to ensure that
the corresponding file descriptor is actually a tap device. For
this reason, qrap now operates on a 'socket' back-end type,
accounting for and building the additional header reporting
frame length
- provide a demo script that sets up namespaces, addresses and
routes, and starts the daemon. A virtual machine started in the
network namespace, wrapped by qrap, will now directly interface
with passt and communicate using Layer 4 sockets provided by the
host kernel.
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
|
