| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
|
|
| |
Now that we install the binary in /bin, and we have a link from
/usr/bin, change the path in the test itself as well. Otherwise
it works with bash but not with dash for some reason.
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
|
| |
|
|
|
|
|
|
| |
We can't get rid of qrap quite yet, but at least we should start
telling users it's not going to be needed anymore starting from qemu
7.2.
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
|
| |
|
|
|
|
|
|
|
|
|
|
| |
Now that we require 13c6be96618c ("net: stream: add unix socket")
in qemu to run the tests, we can also assume that commit df8d07081718
("virtio-net: fix bottom-half packet TX on asynchronous completion")
is present, as it was merged before that one.
This fixes the issue we attempted to work around in passt TCP and
UDP performance tests: finally drop that stuff.
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
|
| |
|
|
|
|
|
|
|
|
|
| |
qemu commit 13c6be96618c ("net: stream: add unix socket") introduces
support for native AF_UNIX support, finally making qrap useless.
We can't quite drop that yet until a qemu release includes it, and
then we'll need to wait a while for users to switch anyway, but at
least for tests, we can use that support.
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
As pasta now configures that target network namespace with
--config-net, we need to wait for addresses and routes to be actually
present. Just sending netlink messages doesn't mean this is done
synchronously.
A more elegant alternative, which probably makes sense regardless of
this test setup, would be to query, from pasta, addresses and routes
we added, and wait until they're there, before proceeding.
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
|
| |
|
|
|
|
|
|
|
|
|
|
| |
Now that we allow loopback DNS addresses to be used as targets for
forwarding, we need to check if DNS answers come from those targets,
before deciding to eventually remap traffic for local redirects.
Otherwise, the source address won't match the one configured as
forwarder, which means that the guest or the container will refuse
those responses.
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
With --dns-forward, if the host has a loopback address configured as
DNS server, we should actually use it to forward queries, but, if
--no-map-gw is passed, we shouldn't offer the same address via DHCP,
NDP and DHCPv6, because it's not going to be reachable.
Problematic configuration:
* systemd-resolved configuring the usual 127.0.0.53 on the host: we
read that from /etc/resolv.conf
* --dns-forward specified with an unrelated address, for example
198.51.100.1
We still want to forward queries to 127.0.0.53, if we receive one
directed to 198.51.100.1, so we can't drop 127.0.0.53 from our list:
we want to use it for forwarding. At the same time, we shouldn't
offer 127.0.0.53 to the guest or container either.
With this change, I'm only covering the case of automatically
configured DNS servers from /etc/resolv.conf. We could extend this to
addresses configured with command-line options, but I don't really
see a likely use case at this point.
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Seen in a Google Compute Engine environment with a machine configured
via cloud-init-dhcp, while testing Podman integration for pasta: the
assigned address has a /32 netmask, and there's a default route,
which can be added on the host because there's another route, also
/32, pointing to the default gateway. For example, on the host:
ip -4 address add 10.156.0.2/32 dev eth0
ip -4 route add 10.156.0.1/32 dev eth0
ip -4 route add default via 10.156.0.1
This is not a valid configuration as far as I can tell: if the
address is configured as /32, it shouldn't be used to reach a gateway
outside its derived netmask. However, Linux allows that, and
everything works.
The problem comes when pasta --config-net sources address and default
route from the host, and it can't configure the route in the target
namespace because the gateway is invalid. That is, we would skip
configuring the first route in the example, which results in the
equivalent of doing:
ip -4 address add 10.156.0.2/32 dev eth0
ip -4 route add default via 10.156.0.1
where, at this point, 10.156.0.1 is unreachable, and hence invalid
as a gateway.
Sourcing more routes than just the default is doable, but probably
undesirable: pasta users want to provide connectivity to a container,
not reflect exactly whatever trickery is configured on the host.
Add a consistency check and an adjustment: if the configured default
gateway is not reachable, shrink the given netmask until we can reach
it.
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
|
| |
|
|
|
|
|
|
|
| |
A number of functions describe themselves as taking a pointer to 'sin_addr
or sin6_addr'. Those are field names, not type names. Replace them with
the correct type names, in_addr or in6_addr.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
|
| |
|
|
|
|
|
|
|
|
|
|
| |
We recently converted to using struct in_addr rather than bare in_addr_t
or uint32_t to represent IPv4 addresses in network order. This makes it
harder forget to apply the correct endian conversions.
We omitted the IPv4 addresses stored in struct tap4_l4_t, however. Convert
those as well.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
We recently corrected some errors handling the endianness of IPv4
addresses. These are very easy errors to make since although we mostly
store them in network endianness, we sometimes need to manipulate them in
host endianness.
To reduce the chances of making such mistakes again, change to always using
a (struct in_addr) instead of a bare in_addr_t or uint32_t to store network
endian addresses. This makes it harder to accidentally do arithmetic or
comparisons on such addresses as if they were host endian.
We introduce a number of IN4_IS_ADDR_*() helpers to make it easier to
directly work with struct in_addr values. This has the additional benefit
of making the IPv4 and IPv6 paths more visually similar.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
This macro checks if an IPv4 address is in the loopback network
(127.0.0.0/8). There are two places where we open code an identical check,
use the macro instead.
There are also a number of places we specifically exclude the loopback
address (127.0.0.1), but we should actually be excluding anything in the
loopback network. Change those sites to use the macro as well.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
There are several minor problems with our parsing of IPv4 netmasks (-n).
First, we don't reject nonsensical netmasks like 0.255.0.255. Address this
structurally by using prefix length instead of netmask as the primary
variable, only converting (and validating) when we need to. This has the
added benefit of making some things more uniform with the IPv6 path.
Second, when the user specifies a prefix length, we truncate the output
from strtol() to an integer, which means we would treat -n 4294967320 as
valid (equivalent to 24). Fix types to check for this.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The INADDR_LOOPBACK constant is in host endianness, and similarly the
IN_MULTICAST macro expects a host endian address. However, there are some
places in passt where we use those with network endian values. This means
that passt will incorrectly allow you to set 127.0.0.1 or a multicast
address as the guest address or DNS forwarding address. Add the necessary
conversions to correct this.
INADDR_ANY and INADDR_BROADCAST logically behave the same way, although
because they're palindromes it doesn't have an effect in practice. Change
them to be logically correct while we're there, though.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
These show a summary of memory usage in kernel and userspace with
different port forwarding configurations, details of userspace usage
using 'nm' (passt only uses statically allocated memory), and details
of kernel memory from slab reporting facilities.
This adds a new test image, mbuto.mem.img, with harcoded IPv4 and
IPv6 addresses and routes, and just the tools we need to start and
stop passt, to report from /proc/slabinfo, /proc/meminfo, and to
print and parse symbol sizes using nm(1).
passt can't pivot_root() for sandboxing purposes on ramfs, so we need
to create another filesystem and chroot into it, first.
We don't want to use pane context functions, as we're checking memory
usage for sockets: resort to screen-scraping.
Configure a dummy interface to provide passt with an appearance of
working IPv4 and IPv6 connectivity, contributed by David.
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
|
| |
|
|
|
|
|
| |
This can be used for generic cell values with an arbitrary scale.
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
|
| |
|
|
|
|
|
|
|
| |
Instead of just disabling performance reports if running in demo
mode. This allows us to use table functions outside of performance
reports.
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
On ramfs, connecting to a non-existent UNIX domain socket yields
EACCESS, instead of ENOENT. This is visible if we use passt directly
on rootfs (a ramfs instance) from an initramfs image.
It's probably wrong for ramfs to return EACCES, but given the
simplicity of the filesystem, I doubt we should try to fix it there
at the possible cost of added complexity.
Also, this whole beauty should go away once qrap-less usage is
established, so just accept EACCES as indication that a conflicting
socket does not, in fact, exist.
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
|
| |
|
|
|
|
|
|
|
|
|
| |
I'm going to add yet another one of those, for which I have no quick
solution. It's a regression in some sense, but at least if we make
this regression more observable and defined, it should be easier to
find a comprehensive solution later, within this or another testing
framework.
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
|
| |
|
|
|
|
|
|
|
|
| |
Unfortunately Bugzilla doesn't enable sharing of queries to
unregistered users:
https://bugzilla.mozilla.org/show_bug.cgi?id=400063
...but we can still use ugly search links.
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
|
|
|
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
|
